![]() The same functionality can be achieved with the 'su' command and disabling the 'root' user from SSH does not effect the functionality of the 'su' command. But I'm not sure why you want 'sudo' so badly. ![]() Didn’t update HA, nor did I change anything in Synology.I realize that 'sudo' is a more common command than the built-in 'su' command. Zigbee2MQTT:error 00:13:58: Error: Connection not initialized Zigbee2MQTT:error 00:13:57: Check for possible solutions Zigbee2MQTT:error 00:13:57: Failed to start zigbee Zigbee2MQTT:error 00:13:57: Error while starting zigbee-herdsman I can see ttyAMC1 in Synology SSH when I type lsusbīut for some reason it disappeared from Home Assistant, and zigbee2mqtt is failing to connect. Home Assistant is running in a Virtual Machine. I followed the above steps and I believe that I’m on the right track, however Home Assistant is failing to see the SONOFF stick form Settings>Hardware>All Hardware. All I had to do is to mount it again from DSM control panel! The VM for some reason lost connection with the dongle. (/app/node_modules/zigbee-herdsman/src/adapter/deconz/driver/driver.ts:200:28)Īt SerialPort._error think the origin of the error could be here: Error while opening serialport 'Error: Error: No such file or directory, cannot open /dev/ttyUSB0'Īt SerialPort._error someone help me to find the solution to my issue?Įdit: found the culprit! It took me several hours to figure it out. ![]() Zigbee2MQTT:error 20:41:52: Error: Error while opening serialport 'Error: Error: No such file or directory, cannot open /dev/ttyUSB0'Īt SerialPort. Zigbee2MQTT:error 20:41:52: Check for possible solutions Zigbee2MQTT:error 20:41:52: Failed to start zigbee Zigbee2MQTT:error 20:41:52: Error while starting zigbee-herdsman I get this error even after following the steps on this feed and can see properly the ttyUSB0 device when listing under dev$ directory. ![]() Let me tell you that I’m running mosquito-mqtt docker with no issues under Synology NAS and that issue is after installing docker of zigbee2mqtt and try to start up the docker service. I can’t maintain my mqtt2zigbee installation up. Modderhut: cp ~/DSM-USB-DRIVER/dsm7-usb-serial-drivers/modules/geminilake/dsm-7.2/cp210x.ko /lib/modulesīash ~/DSM-USB-DRIVER/dsm7-usb-serial-drivers/usb-serial-drivers.sh startĭear all, I have read all the post carefully but still can’t solve my issue. cp ~/DSM-USB-DRIVER/modules/xxxxxxxx/dsm-7.2/cp210x.ko /lib/modulesīash ~/DSM-USB-DRIVER/usb-serial-drivers.sh startĪfter this I could start the DECONZ add-on and the Conbee II was seen again. Optionally you can add these tasks to the task manager in Synology to run at start or manual when the device is rebooted. Sudo sh /usr/local/etc/rc.d/usb-serial-drivers.sh start Sudo cp ~/DSM-USB-DRIVER/usb-serial-drivers.sh /usr/local/etc/rc.d/ Sudo sh ~/DSM-USB-DRIVER/usb-serial-drivers.sh start Sudo chmod +x ~/DSM-USB-DRIVER/usb-serial-drivers.sh Replace the xxxxxx with your CPU package arch name from What kind of CPU does my Synology NAS have? - Synology Knowledge Center sudo cp ~/DSM-USB-DRIVER/modules/xxxxxxxx/dsm-7.2/cp210x.ko /lib/modules You need to have SynoCommunity installed in the package center on yourĬonnect with a terminal to the Synology and do next command one by one git clone ~/DSM-USB-DRIVER/ I mainly used the link posted, thanks! this needed a few tweaks so for the not so techn ical users like me, this is what worked for me, off course all credits to the original poster Scrapix! The VM did see both USB devices but DECONZ did see the stick disconnected. I can confirm I have it all working now on my Synology DS1019+ where I have HA running on a virtual machine. show originalĭid the upgrade yesterday and ran also into this problem, my Arduino RFlink came back fine but my ZigBee II usb stick did not connect to DECONZ. Thus we need to enable some USB drivers plus download one driver and enable this on the system.įor future DSM updates we need to add a Scheduled Task, so that the drivers will be loaded. Additionally one important driver is not available on Synology DSM 7+. Adding Sk圜onnect Dongle according to () or better () Not sure what I am doing wrong.įollowed below document as well. I have followed the same steps but for my NAS 1621+ drivers (taken from V1000) but still issue not fixed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |